Welcome to the official website of Shenzhen Fulikai Packaging Products Co., Ltd.

Shenzhen Fulikai Packaging Products Co., Ltd.

With 19-year experience in manufacturing & customizing EVA foam products.Certified by Coca-Cola, Walmart & Sedex, supporting factory audits.

Custom Service Hotline+86 13827489472+86 0755-29018797

Fulikai - Fast production and delivery within 15 days
Your position: Home > Blog

Can buyers reuse letter and number inventory for an earlier project's foam bath letter and number sets?

Back to list Release Date: 11/22/2026

Yes. In most cases a set of letters or numbers you already paid for can carry over to a later order — provided the character outline, sheet thickness and print method still match what the new SKU requires. The cutting die is usually the expensive part of an alphabet program; the print plate is not. Before telling your supplier to "use the old tooling again", work through the checks below so you know which costs transfer and which ones do not.

What a previous project actually leaves behind

A bath alphabet order normally produces three separate assets, and each behaves differently while it sits idle between orders:

  • The cutting die or laser file. We cut custom shapes by stamping and laser cutting, based on customer drawings or samples. The die is a physical tool held at the factory; the vector file can be re-output whenever you need it. If the character outline on the new SKU is identical, this asset transfers intact.
  • The heat-transfer print plate. Printing on EVA foam uses self-developed heat-transfer technology with multi-pass white-base printing, so colour sits on the surface instead of soaking into the foam. Plates cost far less than a die — our custom-capabilities page lists sample plates at only a few hundred dollars, with a five-day plate-making turnaround.
  • The colour formula. Colour is introduced at the foaming stage through masterbatch, so an exact shade matched on a previous run can be repeated without a fresh compounding job, as long as you keep the same base foam grade.

The practical conclusion: reusing an old letter set usually saves tooling money and one round of sample approval. It rarely saves anything on printing, because a new plate is cheap and quick to make in any case.

Four checks before you approve the reuse

CheckWhat has to matchIf it does not match
Glyph geometryThe exact outline of each letter and digit, including stroke width and corner radius.A new die is needed. Corner radius matters: our bath sets are specified with smooth, burr-free edges, so any re-cut has to reproduce that profile.
Sheet thickness and densityThe gauge the old die was built for, plus foam hardness.A die made for a thinner sheet can crush or feather a thicker one. Confirm the gauge before you budget for reuse.
Finished character sizeOverall height per piece. Our listed bath letter sets are specified at roughly 3 inch, while our EVA alphabet set is specified at 2.5–3 inch.A size change means a new die, plus a re-check of pack layout and any mesh bag or window box.
Print versus plain cutWhether the earlier project printed characters onto the foam or cut the character shape itself.These are different processes. A cut-letter die cannot move into a printed-letter SKU without re-engineering artwork and registration.

Where reuse breaks down in real orders

Three situations come up repeatedly with alphabet SKUs, and each one changes what "reuse" means:

  • script or language change. Latin A–Z tooling does not transfer to a Cyrillic or Spanish set. Our multilingual EVA foam alphabet puzzle mats are listed as two separate language SKUs for exactly this reason — the character inventory differs, not just the print.
  • Set composition change. A 26-piece set (A–Z only) and a 36-piece set (A–Z plus 0–9) share twenty-six dies but need ten new ones. Our EVA foam bath letters and numbers is listed at 36 pieces: 26 uppercase letters plus 10 digits. Extending an older A–Z program to a 36-piece count is therefore partial reuse, not full reuse.
  • Substrate change. Foam letters with a magnetic backing for a fridge surface and floating bath letters that cling to a wet tub wall are different products with different adhesion behaviour. Our magnetic alphabet puzzle carries full magnetic backing on every piece, which a plain bath letter die does not allow for.
Rule of thumb: if the character outline, thickness and size are unchanged, expect to pay for material, printing and labour only. If any one of those three moves, budget for a new die plus a fresh sample round before you commit the order quantity.

How to hand over old inventory cleanly

The fastest way to confirm reuse is to give the factory something physical plus something written. Send:

  • A sample piece taken out of the previous production run, not a pre-production prototype — the die has wear you want reflected in the new batch.
  • The original drawing or vector file with its dimension callouts, if your team still holds it.
  • The reference number of the earlier order, so the factory can pull the stored die and inspect its condition.
  • Your destination country. Raw material selection is market-dependent, and we recommend foam grades that meet the applicable national standard rather than assuming last year's formula still suits a new market.

With those four items in hand the review step is short: our service team checks your drawing against the stored tooling, flags any detail worth improving — linework and corner radius are the usual candidates — then returns design drafts with the quotation. That is the same consultation-to-quotation sequence we run for brand-new programs, just with one line item removed.

What still needs re-approval even when the die is reused

  • Print proof. A new plate means a new proof. Heat-transfer results shift with foam colour and batch, so approve a printed sample before bulk runs start.
  • Colour match. One-step foaming with masterbatch gives consistent colour, but a different base resin or a different market grade can move the shade. Approve against your physical reference piece.
  • Packaging and piece count. Going from 26 pieces to 36 changes the bag, the insert and the carton count. Some of our alphabet configurations ship in mesh bags with suction cups, so pack layout is part of the change rather than an afterthought.
  • Testing. Every production run passes through in-process tests — colour fastness, tensile strength, ink environmental testing and children's product safety testing among them — and every shipment goes through full manual inspection before dispatch. A reused die does not reduce that scope.

Cost and timing you can plan around

With tooling already on site, plate-making takes 5–7 days and bulk orders can be delivered within 15 days. Without a new die to cut, the front end of the schedule shortens by roughly one sample-approval loop. For buyers restocking a proven SKU season after season, that margin is often what decides whether you make a promotional window or miss it.

Bring us your old set. If you hold letter or number inventory out of an earlier program, send a sample piece and the original artwork to our custom EVA foam manufacturing team, or call +86 13827489472. We will tell you which tools can be reused, what has to be re-cut and what the order actually costs — before you place it.

News center

Tel

+86 13827489472
  • Tel

    +86 13827489472

  • E-mail

    sales@fulikaisz.com.cn

  • Add

    5th Floor, Building B, Yuanfen Industrial Zone, Dalang Street, Longhua District, Shenzhen, China

Copyright © Shenzhen Fulikai Packaging Products Co., Ltd. Main business: Puzzle mat, EVA nail file, EVA educational toy, EVA slippers, EVA foam.
Blog