Welcome to the official website of Shenzhen Fulikai Packaging Products Co., Ltd.

Shenzhen Fulikai Packaging Products Co., Ltd.

With 19-year experience in manufacturing & customizing EVA foam products.Certified by Coca-Cola, Walmart & Sedex, supporting factory audits.

Custom Service Hotline+86 13827489472+86 0755-29018797

Fulikai - Fast production and delivery within 15 days
Your position: Home > Blog

Which units and measurement points should be used for taper height and floor contact area on EVA foam door stoppers?

Back to list Release Date: 11/19/2026

Taper height and floor contact area are the two dimensions that decide whether an EVA foam door stopper actually holds a door. They are easy to specify wrongly, because one is measured through the foam and the other describes how much of the bottom face rests on the floor. This note sets out which unit to put on the drawing, where to place each measurement point, and what to write in your purchase order so that the factory and the inspection team read the same numbers.

Use millimetres throughout, and state the unit once at the top of the drawing

For a part this small, work in millimetres. Centimetres appear often in retail listings for door stoppers, but they round away the tolerance you actually care about: half a millimetre of height disappears from a spec sheet written to one decimal place in centimetres, yet it is exactly the difference between a wedge that slides under the door and one that jams against it. Write "all dimensions in mm" above the dimension table, then keep the drawing, the sample request and the inspection instruction in that same unit.

Use inches only where a marketplace page or shelf card needs them, and place them in brackets after the millimetre value rather than in place of it. The production file, the sample approval sheet and the pre-shipment checklist should all carry millimetres, so nobody has to convert twice and get it wrong once.

Taper height: record three points, not one figure

Taper height is the vertical distance from the floor to the top of the wedge at a chosen point along its length. Because the piece is stamped or laser-cut from a foamed sheet, that height changes along the slope, so a single number on the drawing leaves too much room for interpretation. Mark three points on your artwork:

  • Point A, the leading edge, where the slope meets floor level. This edge has to slide home under the door leaf without catching or curling up.
  • Point B, the mid-slope reference, taken halfway between the leading edge and the high end. This is the figure you quote when a buyer asks for "the taper height" as one number.
  • Point C, the high end, measured on the face that sits in the door gap. This controls how far the stopper holds the door open and whether it clears the underside of the door.

Measure each point with the stopper lying flat on a hard, level surface and a steel rule held square to that surface. Do not press the rule into the foam and do not measure while holding the piece: high-elasticity EVA springs back after being squeezed, so a loaded measurement reads low. Note in your inspection instruction that readings are taken unloaded, at room temperature, on the finished printed piece rather than on a bare cutting blank.

Our published listing gives the overall size as 95 × 73 × 18 mm. That is the bounding box of the whole piece — length, width and maximum height — not a taper height by itself. Keep the bounding box and the three taper heights on separate lines in your specification so the two are never confused when goods arrive.

If you can only send one number to a buyer, send Point C together with the door thickness range the stopper is approved for. Those two figures answer the question a shopper actually has: will it fit my door.

Floor contact area: define the footprint before anyone measures it

Floor contact area is not the surface area of the stopper. It is the footprint — the part of the bottom face that rests on the floor once the door leans on the wedge. The distinction matters both for safety claims and for retail listings, because a stopper with a narrow footprint can tip or creep sideways even when the foam itself is firm and tear-resistant.

Agree on one reporting method and write it into the specification:

  • Nominal footprint: length times width of the bottom face, read from the drawing. This is the figure for the carton label and the product page.
  • Contact footprint under load: place the stopper on paper, load it as a door would load it, release it, then measure the outline left by the bottom face. This is the figure for the functional check.

Report both in square millimetres or in square centimetres and pick one as your standard; mixing cm² on the drawing with in² on the inspection sheet is where arguments begin. For incoming goods, a simple rule works better than an absolute area: compare the traced contact footprint with the nominal footprint and set the acceptable ratio. That single comparison exposes cutting and moulding faults without anyone arguing about how soft the foam feels.

Check taper height against the door thickness range

The listing states that this stopper fits doors with a thickness of 3–5 cm, so taper height and door thickness have to be approved together before an order is confirmed. Collect real door edges from your target market — solid timber interior doors, hollow-core doors, and the metal-framed doors used in schools and kindergartens all behave differently — and fit sample stoppers to them. Record three things: whether the leading edge slides home, whether the high end holds without rocking, and whether the bottom face stays flat on the floor coverings your buyers actually have.

Floor covering changes the result more than any other variable, because carpet pile absorbs part of the height. If you are selling into homes with carpeted bedrooms and hallways, say so in the enquiry and ask for the sample to be tested on a carpet swatch as well as on hard tile or laminate.

What the specification sheet should contain

Line itemUnit and how it is taken
Bounding box (length × width × maximum height)mm, from the finished piece, unloaded
Taper height at Point A, Point B, Point Cmm, rule square to a hard flat surface
Nominal floor footprintmm or cm, from the drawing
Contact footprint under load, and minimum acceptable ratio to nominalmeasured from the traced outline after loading
Approved door thickness rangestate as a range, with the floor covering tested
Material, colour and decoration methodcoloured EVA foam; silk screen or heat-transfer printing

Fix the commercial terms in the same document so nothing has to be reopened later. The published terms for this item are OPP bags with customised packaging on request, a sample fee of 600.00 per design subject to the customer's artwork, 5–7 working days for samples, and 25–30 working days for production after sample confirmation, adjusted to actual order conditions. Payment runs as a 30% advance with the balance of 70% released after the pre-shipment inspection is passed.

How these two dimensions are checked in our factory

We are a Shenzhen EVA foam products manufacturer, and door stoppers sit in our household range alongside interlocking mats, kneeling pads and swimming kickboards. Shapes are produced by stamping and laser cutting from customer drawings or samples, which is precisely why we ask for the measurement points to be drawn onto the artwork instead of described in an email — the tooling options are set out on our custom EVA foam manufacturing page.

Orders pass through 16 types of test during production, covering colour fastness, tensile strength, ink material testing and children's product safety among others, and finished pieces are inspected by hand before shipment. We support third-party inspection and buyer audits at the factory. If your quality agreement defines taper height at Points A, B and C plus a minimum contact footprint, our inspectors and their inspectors work to the same lines on the same unit.

Before you place the order

Send one drawing with the unit stated once, three taper heights, both footprint figures, and the door thickness range you need covered. Approve a physical sample against that sheet and keep the approved sample as the reference for incoming inspection: a signed sample settles a dimension argument far faster than any email thread.

Send us your drawing or a door edge sample and we will return a proposal with the measurement points marked on it.
Hotline +86 13827489472 · Email sales@fulikaisz.com.cn · Contact Fulikai

News center

Tel

+86 13827489472
  • Tel

    +86 13827489472

  • E-mail

    sales@fulikaisz.com.cn

  • Add

    5th Floor, Building B, Yuanfen Industrial Zone, Dalang Street, Longhua District, Shenzhen, China

Copyright © Shenzhen Fulikai Packaging Products Co., Ltd. Main business: Puzzle mat, EVA nail file, EVA educational toy, EVA slippers, EVA foam.
Blog