Tile warping, chipped corners and scuffed faces rarely show up in the first inspection photo. They appear after a carton has been stacked in a container for thirty days. For buyers of waterproof EVA mahjong tiles, packaging is not decoration — it is part of the dimensional and print tolerance chain. This guide shows what to specify, what to inspect, and how to prove that the packing protected the product.
EVA is a closed-cell foam. It is light, buoyant and water-repellent, which is exactly what makes it useful for pool games: our floating American mahjong sets are made from this material so the tiles float instead of soaking up water. The same softness means a tile edge will take a set under sustained pressure. A hard acrylic tile resists a corner crush; a foam tile bends and, if the bend lasts long enough or the temperature is high enough, it stays bent.
Printed faces are the second exposure. Our heat transfer printing on EVA foam fuses the artwork into the surface, so it does not peel like a sticker under normal use. But two printed faces pressed together under load for weeks can abrade against each other where the film is still warm from the factory. That shows up as faint scuffing or a loss of gloss along the tile edge, and it is a packing problem, not a printing defect.
| Variable | What goes wrong when it is wrong | What to write on the purchase order |
|---|---|---|
| Inner pack | Loose tiles knock corners off each other; printed faces rub face-to-face | Set bag, interleave or tray — state which one, and whether faces touch |
| Carton wall grade and stack height | Bottom cartons crush under the stack, tiles bend into a curve | Paper grade plus maximum stack height in the container plan |
| Cushioning and void fill | Tiles shift in transit; edges hit the carton wall | Corner protectors or foam sheet between layers, no movement when a sealed carton is shaken |
| Temperature exposure | Heat softens the foam, so a compression that would be harmless in a cool warehouse leaves a permanent bend | No pallet shrink-wrap left in sun; keep cartons off hot container floors |
Our standard sets ship as a complete kit — 160 tiles, four EVA dice and a drawstring storage bag in one unit, so the set itself is already contained. For retail programs we change that on request: OPP bag per set, colour box, or a mesh bag with a suction cup for water toys are all normal options at our factory. Tell us which one you want, because each has a different effect on the tiles:
Foam sets are light, so buyers often assume the carton can be thin. The load on a carton is not the weight of its own contents; it is everything stacked above it. Specify the paper grade and state the maximum stack height in your container plan, then check that the pallet diagram on the packing list matches it. If you want to know how much room the set takes before you commit, ask for the packed dimensions and gross weight per carton with your quotation.
A sealed carton that sounds like marbles rolling inside will arrive with chipped tile corners. A quiet carton means the void is filled. Ask for corner protectors or a foam sheet between layers when tiles are shipped loose, and run the shake test on your pre-production sample rather than on the first production carton.
Our own product care notes for EVA items tell users to avoid long exposure to direct sunlight or high temperatures, because heat can age, deform or discolour the foam. That advice applies to your goods before they reach the customer. A carton compressed on a hot dock or in a sun-exposed yard will take a set that a cool warehouse never produces. Note it in the shipping instruction: keep cartons out of direct sun, do not leave pallets wrapped and standing on hot surfaces, and avoid stacking anything heavy on top of game sets.
Flatness test. Lay twenty tiles from different cartons, taken from different heights in the stack, face down on a flat table. Press a corner lightly; if it rocks or lifts, the tile has bowed. Compare tiles from the top carton and the bottom carton — a difference between them points at stacking pressure, not at the moulding.
Edge and marking test. Under a raking light, look along each edge for chips and nicks, and across the printed face for scuff lines or dull patches. Edge damage concentrated on one side of the tile points to loose packing; scuffs in the middle of the face point to face-to-face contact.
Float and fit test. Put a sample of tiles in water and confirm they float level rather than tilted, then place them in the tile grooves of your floating mahjong table. A tile that sits crooked in the slot or floats on a tilt has deformed. Tile slots are cut to size — one of our double-sided trays uses 25 mm double-row slots, and the practice board uses deep 0.39-inch slots — so a bent tile is visible to the end user immediately.
Because we run foaming, cutting, stamping and laser processing in our own Shenzhen factory, the material and the packing can be changed together instead of negotiated between two suppliers. Colour goes in at one-step foaming with masterbatch, so there is no surface coating that cracks when a tile flexes. On custom EVA foam manufacturing orders we support 100% third-party inspection and buyer audits, every product passes through production tests including colour fastness and tensile strength, and every shipment goes through full manual inspection before it leaves the floor. If your packing specification calls for interleaving or a tray, that change is made in the same conversation as the artwork.
Do waterproof EVA tiles absorb water in the carton?
No. Closed-cell EVA does not soak up water, which is why the tiles keep their buoyancy through long play. Water damage in transit is almost always about heat and pressure on the packed carton, not absorption.
Can I change packing after the plates are made?
Yes for inner pack and carton specification; plate-making takes 5–7 days and is separate from packing tooling. A tray or blister does need its own tooling, so decide on it before you approve the design draft.
What should I do if tiles arrive bowed?
Photograph the carton stack in the container first, then run the flatness test on tiles from the top and bottom cartons separately. If only lower cartons are affected, the cause is stack load or carton grade; if all cartons show it, look at heat exposure or the packing insert pressure. Send us both photos and we will trace it with you.
Send us your inner-pack choice, carton grade, stack plan and destination market, and we will confirm the packed dimensions and gross weight per carton with the quotation. That single step is what separates a set that arrives flat from a set that arrives curved.
Send your packing specification with your enquiry. Shenzhen Fulikai Packaging Products Co., Ltd. — sales@fulikaisz.com.cn, +86 13827489472. Contact us to start a custom EVA foam order.
Shenzhen Fulikai Packaging Products Co., Ltd. — EVA foam products manufacturer since 2008, exporting to Japan, South Korea, Europe and the United States.
Tel
+86 13827489472
+86 13827489472
sales@fulikaisz.com.cn
5th Floor, Building B, Yuanfen Industrial Zone, Dalang Street, Longhua District, Shenzhen, China