Welcome to the official website of Shenzhen Fulikai Packaging Products Co., Ltd.

Shenzhen Fulikai Packaging Products Co., Ltd.

With 19-year experience in manufacturing & customizing EVA foam products.Certified by Coca-Cola, Walmart & Sedex, supporting factory audits.

Custom Service Hotline+86 13827489472+86 0755-29018797

Fulikai - Fast production and delivery within 15 days
Your position: Home > Blog

Which units and measurement points should be used for inspection points for EVA foam production inspection?

Back to list Release Date: 11/18/2026

Ask three factories what tolerance applies to a custom EVA foam part and you will get three different answers. One quotes millimetres, one quotes inches, and one says "about the same as your sample". The disagreement is rarely about capability. It is about units and reference points not being agreed before the first sheet is foamed. This guide sets out the units we use at Fulikai, where we measure on each part, and what a buyer should put in writing so that an inspection report and a purchase order describe the same thing.

Start With One Unit of Measure, Not Two

EVA foam parts on our catalogue are dimensioned in inches for North American retail programmes and in millimetres for European buyers and for tooling drawings. Mixing the two inside one specification is the most common source of inspection disputes, because a buyer reading 0.8 inch and a QC inspector reading 20 mm are not comparing identical numbers — 0.8 inch is 20.32 mm.

Our working rule is simple. Pick the unit your customer-facing listing uses, state it once at the top of the specification, and let the factory convert for tooling. Where a product page already carries both values, such as the EVA yoga mat listed at 71 inch by 24 inch with a quarter-inch thickness, or the kneeling pads listed in inches while their mould drawings are metric, the primary unit is the one on the retail listing and the converted value is for reference only. Tolerances are then applied to the primary unit.

The Measurement Points We Record on Every Order

A dimension without a stated measurement point is not verifiable. For each part we record the following, and buyers can ask for the same list in their own inspection instructions.

1. Overall length, width and thickness on the finished part

Length and width are measured across the widest points of the finished, relaxed part — not of a sheet before cutting. Thickness is measured at the centre of the part, away from any cut edge, because stamped and laser-cut edges compress slightly. A garden kneeling pad such as our 18 by 11 inch kneeling pad is checked on the flat top surface, since its working dimension is cushioning height under load.

2. Thickness at three positions for foam sheets and mats

Foam thickness varies across a foamed block. We measure at the centre and at two opposite edges of each piece rather than one point, and we reject pieces whose spread exceeds the agreed band. This matters most on high-density products where a thin edge means the part will bottom out in use — the high-density EVA garden kneeling pad is a typical example.

3. Density and hardness, which are not dimensions at all

Two parts with identical dimensions behave differently if the foam differs inside. Density is recorded as mass per unit volume in kilograms per cubic metre, and firmness is recorded by durometer on a Shore scale. Buyers specifying "high-density EVA" should state the target density range and the durometer they expect, otherwise two production runs can both pass a dimensional check and still feel different on the shelf.

4. Print area position and colour

For printed parts we measure from a defined edge of the part to two corners of the artwork, so that placement drift is visible in the report instead of being judged by eye. Colour is checked against a physical masterbatch-matched swatch signed off before production, under agreed lighting, because our colours are formed during one-step foaming with colour masterbatch and cannot be corrected afterwards the way an ink can.

5. Functional fit points

Some parts live or die on one dimension that is not on the drawing's main block. A door stopper must match the door thickness it grips. A floating game mat must hold tiles in their grooves without lifting on a ripple. Where a functional fit exists, we list that point as a separate inspection item with its own pass condition.

Test Methods That Have Their Own Units

Alongside dimensions, our production process includes sixteen types of test across the order run. These carry units buyers should specify rather than assume:

  • Colour fastness — rated on a grey-scale grade after rubbing and washing, not described as "good" or "fine".
  • Tensile strength and tear resistance — force per unit width, reported in newtons.
  • Environmental testing of ink materials — substance limits expressed in milligrams per kilogram, aligned with the REACH and RoHS thresholds for the destination market.
  • Children's product safety testing — small-part dimensions in millimetres against the cylinder gauge used in EN-71 and ASTM-type checks, plus coating and phthalate limits in percentage or milligrams per kilogram.

Certification claims follow the same rule. Our factory operates under an ISO 9001:2015 quality management system and holds CE, EN-71, FDA, FCC, RoHS, SGS and REACH documentation. Which certificate or test report applies depends on the product, the destination market and the order, so we confirm that specific document with the buyer before it is quoted or printed on packaging.

Where Inspection Happens in the Order Timeline

Units and points only matter if someone checks them at a fixed moment. Ours run as follows:

  • At sample approval. Dimensions, colour swatch and print position are signed on the physical sample. That sample becomes the reference for the whole order; numbers on a PDF rank second to it.
  • During production. In-process checks cover thickness spread across the foamed sheet, print registration against the measured corners, and density or firmness on the batch.
  • Before shipment. Every finished unit passes full manual inspection, and we support 100% third-party inspection by an agency of the buyer's choosing. Our pre-shipment process rejects defective units rather than sorting them into a lower grade, and our payment terms tie the balance to passing that pre-shipment inspection.
  • On request at the factory. We hold audit reports from Coca-Cola, Walmart and Sedex and welcome buyer-conducted audits of the Shenzhen site.

What to Write Into Your Purchase Order

Before you send a drawing, add four lines. First, name the single unit of measure and state which value governs if two appear. Second, list the measurement points for thickness, print position and any functional fit, so the inspection report can be matched line by line against your order. Third, state the target density range and durometer instead of an adjective such as "firm". Fourth, name the test standard and the market it applies to, and ask which report will be issued.

Buyers who send that information usually settle quality questions in one exchange rather than five. If you have drawings or samples ready, send them with your unit preference and target density, and our team will return a specification sheet showing the exact points we will measure on custom EVA foam production before the first bulk run starts.

News center

Tel

+86 13827489472
  • Tel

    +86 13827489472

  • E-mail

    sales@fulikaisz.com.cn

  • Add

    5th Floor, Building B, Yuanfen Industrial Zone, Dalang Street, Longhua District, Shenzhen, China

Copyright © Shenzhen Fulikai Packaging Products Co., Ltd. Main business: Puzzle mat, EVA nail file, EVA educational toy, EVA slippers, EVA foam.
Blog